Single Fibre/Mode (SC-1550nm) with Link Failure Propogation, 80Km

Fast Ethernet 10/100Base-TX to 100Base-FX Single Mode/Single Fibre WDM Media Converter. Models available in 20, 40, 60 and 80Km variations. Alloy offer a complete range of media conversion for Ethernet, Fast Ethernet, Gigabit Ethernet, ATM, and asynchronous Serial Networks over various interface types such as Multimode and Single Mode Fibre Optics, Copper RJ-45 and copper Serial. All Converters are fully compliant with IEEE multi-protocol standards, including 10Base-T/2/FL, 100Base-TX/FX, 1000Base-SX/LX, and ATM protocols. The Converters ship as standard with a mains plug pack, but can also be directly powered from a PC or Notebook via a PS2 keyboard adapter or a spare USB slot (FE-C120 series only). For centralised media conversion a hot-swappable, 10 slot, 19 inch rackmount chassis can be used to provide a single power source for multiple converters. The Rack chassis solution provides various power options from Dual redundant to single power supplies in either Mains AC voltages or Telco 48V DC options. Specificly the FE-C120S3/5 range of converters are used for conversion of 10/100Mbps Ethernet to Fibre 100Base-FX. They are fully compliant with the 802.3u standard and feature one TP RJ-45 10/100Mbps port and one fibre 100Mbps port using a single "SC" connector. The FE-C120S3/5 "single fibre converter" is designed with an optic Wavelength Division Multiplexing (WDM) technology that simultaneously transports a bi-directional full duplex signal over a single fibre. The FE-C120S3/5 is unique in that it adds a manual over-ride function to the 10/100Mbps port selection. This enables the user to force either 10Mbps or 100Mbps at either Half or Full Duplex from easy to access DIP switches mounted on the side of the case. Power for the FE-C120S3/5 range of converters can now be taken from the Host PC or Notebook's USB port. This enables the converters to operate without the necessity of mains power (in the case of a notebook), and without the need for additional power points or mains expansion boards. USB cable is approx 1.5 meters in length. Note: other power options also available. The FE-C120S3/5 range supports 'Link Status Propagation'. This feature enables propagation of the link signal across both ports of the converter and is seen as a critical feature for managed networks that utilize SNMP type trap events to notify network managers of potential problems. 'Link Failure Propagation' can also be used in modern OS's where Ethernet Link loss can atc as a trigger to enable a standby route. The FE-C120S3/5 converters can be installed as standalone units or as a slide-in module to the 19" converter rack ( CR-1000 ) for use at a central wiring closet. These converters must be used as a pair, ie FE-C120S3.S20 connects to FE-C120S5.S20 and visa versa.

Click to Enlarge Image

Product Specification

Connector Types ~ 1x RJ-45 MPR/DTE 100Base-TX UTP Port ~ S3 = 1x 1310nm Fibre Optic SC Connecter ~ S5 = 1x 1550nm Fibre Optic SC Connecter Cable Types Supported ~ RJ-45 Port: UTP Cat 5/5.e ~ Fibre Port - (SC) Single Mode/Single-Fibre WaveLength ~ FE-C120S3.S20 - RX:1550/TX:1310nm ~ FE-C120S5.S20 - RX:1310/TX:1550nm Cable Range ~ RJ-45 Port: 100m max ~ Fibre Optic - Single Mode: 20/40/60Km Data Transfer Rates ~ 100Mbps TP auto-duplex-negotiation ~ 200Mbps for full-duplex mode MAC Address and Self-learning ~ 1K MAC address entries LED Suite ~ FX Link/Act, TX Link/Act, 100Mb, FDX/COL, Power Power Requirement ~ 1A@+5VDC Ambient Temperature ~ 0°C to 50°C Humidity ~ 5% to 90% Dimensions ~ 26.2(H) x 70.3(W) x 158(D) mm Standards Compliance ~ IEEE 802.3u 100Base-TX and 100Base-FX Flow Control ~ IEEE 802.3x for FDX & Back pressure for HDX Approvals ~ C-Tick, FCC Part 15 Class A, CE

Ordering Information