|
Rackmount Gigabit Ethernet Tap with 2x network and 2x monitoring ports with user defined TriggerXtramus NuTAP-R series is the only high-level Ethernet TAP product with the ability to support port aggreagation.
The NuTAP-R series of Ethernet TAP's is the first of it's kind supporting a beneficial rack mount deisgn allowing easy integration to your existing network rack and additionaly allowing easy connection to your existing network infrastructure. It's unique Gigabit design is also market leading and allows full wirespeed transmission as well as capturing all network traffic being monitored. The NuTAP-L series comes with two models supporting 2 or 4 UTP/SFP network interfaces.
The NuTAP-R series is embedded with one Gigabit high-speed memory and a trigger module which can monitor up to 30 networks per line. This allows the user to configure user defined filters to capture the required packets. Up to 60 event counters on each surveillance line can provide important data for network statistics, error detecting, analysis, monitoring and so on.
Major Benefits
- Real-time monitoring and analyzing of network traffic.
- Relay function allows network connectivity if power fails.
- Provides an invisible, non-intrusive permanent access to network monitoring and analysis devices without link disruption or degradation.
- Simultaneous non-blocking forwarding of all TX and RX traffic, including error packets.
- Protects the IDS sensor from attack by the monitored segment.
- Option to withdraw mirroring function to avoid any problems associated with such methods.
- Easy to read counter status.
- Conforms to 19¨ rackmount form factor.
| 
Click to Enlarge Image
|
Product Features| | - Active TAP based on monitor and forward architecture
- Filter supports 8-set 32bits UDF and 2-set 48bits UDF (offset fix at DA/SA).
- Supports full set RMON counter.
- Real-time LED display of traffic events and monitoring
- Packet redirect function:
- Aggregation mode: Up/Down redirect into one
- 1 pair (2 ports) to 2 output port (R12G)
- 2 pairs (4 ports) to 1 output port (R21G)
- Segregation mode: Up/Down redirect separately, individual traffic from 1 pair to individual output port (R12G)
- Swap aggregation / Segregation mode: Controlled by on-panel button, serial port, or web-based management interface
- Error Traffic Redirect
- User friendly design of web-based management interface
- Provides Statistic Counter (30 set individual counter per port)
- Built-in filter to block traffic from specific network port(s) to the monitoring port (Individual 10 sets filter per port, R series and A series).
- Redundant power (DC 48V power input module) optional
- Supports PoE pass through
|
|
Product Specification| |
Network Port:
~ NuTAP-R12G: One pair of one 10/100/1000Mbps RJ-45 and Mini-GBIC combo
~ NuTAP-R21G: Two pairs of one 10/100/1000Mbps RJ-45 and Mini-GBIC combo ports for traffic up to 2 network segments
Monitoring Port:
~ NuTAP-R12G: Two 10/100/1000Mbps RJ-45 and Mini-GBIC combo ports
~ NuTAP-R21G: One 10/100/1000Mbps RJ-45 and Mini-GBIC combo port
Management Port:
~ One 10/100Mbps RJ45 port
Serial Port
~ One RS-232 port for real-time display of traffic statistics
Supported Packet Length
~ 32~16000 bytes
Power Source Type:
~ AC 90V~240V( Standard)
~ DC 48V( exclusive option)
Power Consumption:
~ 7.5~ 13 Watts
Test Criteria:
~ Unicast, Broadcast, Pause Control, Collision, CRC, Undersize, Oversize, Trigger, Capture Loss
Temperature:
~ Operating: 0 C ~ 40 C
~ Storage: 0 C ~ 50 C
Humidity:
~ Operating: 0% ~ 85% RH
~ Storage: 0% ~ 85% RH
Dimensions:
~ 442 mm x 240 mm x 43 mm
|
|
Ordering Information
| | | NUTAP-R12G | Rackmount Gigabit Ethernet Tap with 2x network and 2x monitoring ports with user defined Trigger and Filters | Where to Buy |
| NUTAP-R21G | Rackmount Gigabit Ethernet Tap with 4x network and 1x monitoring port with user defined Trigger and Filters | Where to Buy |
|
|